Proceedings of the 2016 3rd International Conference on Mechatronics and Information Technology

+ Advanced search
160 articles
Proceedings Article

Pilot Study on the Preparation of Fiber Cement Panel using Calcium Silicate Slag

Jiayu Zhan, Chunlei Geng, Feihua Yang, Wanmin Li, Chuang Yang, Zhijie Yang
Calcium silicate slag is a waste discharged during alumina extraction process from fly ash was investigated. In this study, calcium silicate was used as raw material to substitute part of Portland cement to produce fiber cement panel. The fiber cement panel was produced via extruding process. The physical...
Proceedings Article

Study on Preparation and Dyeing Wastewater Adsorption Properties of Carbonized Cotton

Ju Wei, Mengxue Yan, Songjia Lu, Dan Huang
Carbonized waste cotton were prepared by activate solution carbonization method. The effects of moisture content, carbonization time and carbonization temperature on the yield of carbonization were investigated. At the same time, the adsorption property of direct dye of the carbonized cotton products...
Proceedings Article

Strong convergence theorems for k-strictly pseudo-contractIve mapping in Hilbert spaces

Qiuxia Lu, Yan Hao
In this paper, we introduce a general iterative algorithm and prove strong convergence theorems for a non-self k-strictly pseudo-contractive mappings in Hilbert spaces. Our results improve and extend the corresponding results announced by many others.
Proceedings Article

Elasto-plastic analysis of the rotor and wedges supercritical turbo generator

Xingtian Qu, Yongbing Zhao, Jianbing Cheng, Shengyu Wu, Chaopeng Zhang
Under the condition of over speed, the rotor and wedges of the supercritical 1000MW turbo generator are plastically deformed. By using the software ABAQUS for rotor and wedges strength analysis, The results showed that the strength of chamfer at the tooth root of aluminum wedges in rotor, chamfer at...
Proceedings Article

The Analysis of Mercury Flow of Fluorescent Lamps in Mainland China

Sha Chen, Jiaxing Zhang
Fluorescent lamps are increasingly being used for general lighting due to their higher energy efficiency than incandescent lamps. However, they contain mercury, which is a high toxicity element. China is one of the largest fluorescent lamps consuming and producing country in the world and has been facing...
Proceedings Article

Research and Experiments on Electromagnetic Field Induced by Two Coaxial Solenoid Coils of Axially Mag-lev Driving Needle

Yang Liu, Xiaoguang Wu, Chi Zhang, Daoyu Wan, Li Zhu
The movement of mag-lev driving needle depends on the interaction of magnetic fields between two solenoid coils and magnet. Inside single cylinder, two solenoid coils are placed vertically and coaxially while the magnet is laid at the bottom of the needle base. Based on magnetic-levitation theory and...
Proceedings Article

Study on the determination of chitosan by enzymatic hydrolysis-spectrophotometry

Sihui Wu, Yonghe Jiang, Shang Kong, Haitao Pan, Danyuan Xu, Zhengquan Su
Chitosan (CTS) is a natural basic polysaccharide, which have no a very effective way to determine its content now. In this paper, we used cellulase combined with mixed acid under ultrasound assisted (CAU) method to hydrolyze CTS into glucosamine, which can react with diaminobenzene formaldehyde acid...
Proceedings Article

A Study on an Automatic Welder with the New-Type Spiral Heat Exchanger's Pillar Plate

Xingtian Qu, Kun Zhang, Yuzhe Wang, Jinghui Peng, Wenqiang Xu, Xuexu Wang
This paper mainly studys on a kind of new-type automatic welder-an automatic welder with the new-type spiral heat exchanger's pillar plate, the welding process of given-distance pillars in the production process of spiral heat exchangers is invested and analyzed. This paper analyzes the ultimate principle...
Proceedings Article

Study on The Regeneration Performance of Reclamation of The Used Sands Vane Wheel Equipment

Wenlong Lu, Shan Li, Qiang Chen
This paper expounds that the significance of the regeneration of the used sand, design structure, working principle, working mode and advantages of reclamation of vane wheel equipment. The test prototype of reclamation of vane wheel equipment was used to reclaim the used sand, and the clay content of...
Proceedings Article

Cyber-Physical System Security and Protection Strategies for the Smart Substation

Sicheng Zeng, Yimin Qiu, Yongyi Shi
As an important part of the smart grid, smart substation is the key operating parameters collection point and control execution point, thus its safe and stable operation is one of the fundamental bases of ensuring the grid continues to provide a reliable energy resource for the development of the national...
Proceedings Article

The Research on Properties of Functional Fabrics in Home Textiles based on Blue Calico

Lei Zhang, Kehui Deng, Ziqi Wang
In this paper, we take an innovative experiment on one fabric in home textiles based on Blue Calico, to study the plying structure of yarns and properties of the fabric. Under the circumstance of the same warp yarn, we compare these different fabric weaved by a plurality of high count plying yarns without...
Proceedings Article

The Fluid Flow Field Characteristics Analysis of Automobile ABS Storage Tank Based on CFD

Wentao Zhang, Liang Yao
The automobile ABS is an important device for safe driving. The properties of the brake fluid are closely related to the automobile braking efficiency. The gas-liquid two phase flow often occurs in the brake fluid for various reasons, which affects the transmission characteristics of brake fluid pressure...
Proceedings Article

The Research on Evaluation Technology of Lock Chamber Wall

Fangshu Qian, Titao Wang, Hongwei Ding, Xiaojun Chen
Under the influence of natural and human factors, most hydraulic structures will be damaged. Therefore, an index parameter system is proposed to reflect the surface integrity of lock chamber wall, durability and strength, etc. Meanwhile, the corresponding testing technology and testing methods for the...
Proceedings Article

Fabrication of TiO2 / Ag / Ag3PO4 Heterostructured Nanorod Arrays on FTO for Enhanced Photoelectrochemical and Photocatalytic Performances

Wei Liang, Shengling Lin, Chuanxiang Chen, Ankang Chen
This research explores the preparation of TiO2/Ag/Ag3PO4 heterostructured nanorod arrays on transparent conductive FTO glass for the first time. The structures and morphologies of the products were characterized by using scanning electron microscopy (SEM) and X-ray diffraction (XRD). Moreover, their...
Proceedings Article

Kinetic studies on the adsorption of Cu(ll) onto alginate-carboxymethyl cellulose membrance

Xihui Zhao, Xiaolu Sun, Qun Li, Xiaowen Li, Yanzhi Xia
Alginate-carboxymethyl cellulose membrane (AC membrane) was prepared. The adsorption behavior of Cu(II) on AC membrane was studied. The adsorption mechanisms were investigated with three different kinds of kinetic models (Lagergren's pseudo-first-order, Ho's pseudo-second-order equations). The results...
Proceedings Article

The Stress Analysis and Calculation Method of the Poles of Different Arrangement Styles in the Distribution Network Lines and the Research of "Abandoning Wires to Protect Electric Poles" Project

Kai Xiao, Qingchun Hu, Wenping Xie
The force situation of pole was analyzed in detail through the establishment of three-pole model, and the five-pole model was built on the basis of the former model. Besides, the influence of external factors including height difference, span, wind angle and line angle to the pole were studied, and the...
Proceedings Article

The Mechanical Deformation Research of the Annular Ring Based on the Function of the Device of "Abandoning Lines to Protect Electric Poles"

Kai Xiao, Qingchun Hu, Wensheng Li
The device named "abandoning lines to protect electric poles" was mainly used for the weak links of the system of distribution network lines to motion first when the design wind speed was oversize, and the core components of the device were made up with a cutting edge shaft and an annular ring locked...
Proceedings Article

Contrast Analysis on Infrared and Raman Spectra of the Sinomenine Podwer

Xiao-Dong Liu, Lu Liu, Hua-Mao Meng, Sen Gao, Wen Zhang
Contrast analysis on high-resolution infrared and Raman spectra of the sinomenine powder have been performed to work out about sixty really existing vibrational spectral bands. Except for the hydroxyl stretching modes and IR active bands less than 400 cm-1, most normal modes (about fifty) are both IR...
Proceedings Article

The study of capacity and installation of distributed power flow controller

Menglu Gao, Qianguang Yuan, Aihong Tang
This paper deals with the capacity and installation problems of the Distributed Power Flow Controller. There is a rapidly increase in the development of FACTS and the application of it in the power grid. On 500kV power distributed system, the addition of Distributed Power Flow Controller is to change...
Proceedings Article

Collect mechanisms of oleic acid on fluorite and calcite minerals

Dong Lin, Guanghua Nie, Guoju Luo, Zhipeng Tang
The floatability influence of sodium oleate and oleic acid on fluorite, calcite were studied by flotation test. Zeta potential of fluorite and calcite was tested by Zeta Potential Analyzer. By Materials Studio software, the reagent action on mineral surface was simulated and the surface energy changes...
Proceedings Article

Precise electrical characteristics in light emitting diodes on patterned sapphire substrate

Yang Li, Qiongyong Xing
Accurate electrical properties of semiconductor patterned sapphire substrate light emitting diodes large forward bias voltage were measured by alternating current small signal and I-V plot, as well as our self-built method, respectively. Patterned sapphire substrate light emitting diodes display an obvious...
Proceedings Article

A practical approach based on stream of variation for positioning accuracy in precise linear motion stage

Hao Tang, Ji-An Duan, Yu Zheng, Baibing Li
This paper introduces a new analyzing approach on positioning accuracy (PA) in precise linear motion stage (PLMS). As one of the most important parameter, PA is affected by several reasons for the quality of PLMS, such as machining error, assembly error and controller accuracy etc. Conventional method...
Proceedings Article

STRUCTURE OPTIMIZATION OF WHEEL ON FATIGUE FAILURE

Kezhi Linghu, Baoliang Xiao, Ziyuan Lin, Yuncheng Ning, Fengqin Wang, Shaobo Li, Xueqi Huang
Based on the basic truck steel wheel structure design, revised designs such as vent-hole-changed and profile-modified were proposed to solve the common fatigue failure problems .Both basic and modified design were modeled using Abaqus 3D software to calculate the stress and strain contours in the case...
Proceedings Article

Research Status and Development of Corrosion Detection Technology in Buildings

Hongzhou Hui, Fang He, Hongwei Ren, Lei Qin
This paper discusses the significance and research status of steel corrosion detection. This paper briefly analyzes several important detection methods and their application characteristics. The advantages and disadvantages of the present research methods are discussed. It puts forward the necessity...
Proceedings Article

Studies on jute fiber/polypropylene, jute fiber/Polylactide and glass fiber/Polypropylene composites for automotive application

Rui-Hua Hu, Kui-Hua Hu, Guo-Hua Yang
In the past few years, the awareness of environment protection all over the world and the release of strict guideline and regulations concerning automotive end-of-life requirement forced the automakers to seek eco-friendly materials to make car "greener". In this work, three composites are fabricated....
Proceedings Article

Performance analysis and dynamic test of single cylinder diesel engine

Liankun Chi, Lihua Wang, Qi Wang
Some optimization are applied on TBD620 diesel engines in order to enhance its power and reliability and reduce the manufacturing cost. For the study of engine parameters influence on its working process, and reduce the experiment cost, we developed 620 single cylinder machine in the process of improvement...
Proceedings Article

Innovative Design for Vortex Micro-Nano Bubble generator Based on TRIZ

Yanjie Chen
In order to solve the issues of the micro-nano bubble generation technology, that generally exists high energy consumption and low bubble production, TRIZ method of technical contradiction inventive principles was utilized to provide ideas to design a new-type of micro-nano bubble generating device....
Proceedings Article

A Smart Sensors-based real-time decision making system for the Cold Supply Chain

Jinlong Luo, Jianjun Yi, Xiaomin Zhu, Jun Xu
Real-time monitoring of the cold chain logistics and timely decision-making are important means to ensure the quality of the cold supply chain. Therefore, this paper design a smart temperature and humidity tag with ad-hoc network, which can realize regular monitoring of temperature and humidity inside...
Proceedings Article

A cloud-service Home Health Monitoring System for the Older People Based on WBANs

Lin Wang, Jianjun Yi, Xiaomin Zhu, Yi Li
This paper proposes a cloud-service home health monitoring system based on WBANs for tracking the health status of the older people while supporting their mobility. The system consists of a WBANs physiological parameters acquisition system and a remote cloud server. While the former subsystem is responsible...
Proceedings Article

The confirmation of simulation parameter and analysis of temperature field of 430 ferrite stainless steel in water-cooling condition with 3D-CAFE method

Pei-Xiao Liu, Yan-Xiang Li, Rui-Peng Pang
Under water cooling condition, the solidification structure is almost equiaxed grains, and the diameter of equiaxed grains is 0.5 mm~1mm, columnar grains are relative small, columnar grain width is only a few tenths of millimeters, with the length is 0.5 mm~1.5 mm. When the top heat transfer coefficient...
Proceedings Article

A Hydraulic-and-electric Robot Arm for Mobile Manufacturing

Peng Gao, Anye Ren, Zong Wei
This paper proposes a hydraulic-and-electric robot arm for mobile riveting manufacturing. A hydraulic-and-electric robot arm prototype equipped on AGV is designed with 1.5m stretching length, 30kg load and 250kg self weight, which is lighter than commercial robot arm products. It consists of 3 hydraulic...
Proceedings Article

12W UV laser based on Air-cooled Double-end-pumped Intra-cavity

Yuchao Zhou, Shengyu Zhao, Yongquan Zhou, Yuli Song
12W UV laser generator is developed as a second harmonic generator and a third harmonic generator, in which a folded resonance cavity is composed of two laser diode side-pumped Nd:YAG modules, an electro-optic Q-switch, two LBO crystals. The air-cooled double-end-pumped Intra-cavity is studied and designed,...
Proceedings Article

Research on the Distribution of Permanent Magnetic Field in the Magnetic Drive of High-Speed Maglev Circular Knitting Machine

Dao-Yu Wan, Xiao-Guang Wu, Chi Zhang, Li Zhu, Xiao-Long Lei
Research in high-speed maglev knitting drive, through the magnetic and magnetic field analysis of electromagnetic and permanent magnet hybrid drive, establishing the mathematical model of the permanent magnet external magnetic field. Based on theoretical calculation of permanent magnet external magnetic...
Proceedings Article

Study on photochromic properties of metal dithizonate complexes doped PMMA film

Shengwen Qi, Xueping Cheng, Hongguang Lu
The absorption spectra of trans and cis isomers of mercury dithizonate (MD) in doped polymethyl methacrylate (PMMA) film are measured, and the photochromic properties of the two isomers are analyzed individually. The experiments indicate that different isomers of MD can convert into each other when irradiated...
Proceedings Article

Constitutive Model Research on Pure Aluminum Considering Dynamic Recovery and Recrystallization

Tingting Zhou, Yang Yang, Maobing Shuai
The article introduces some main constitutive models of pure aluminum with regard to mechanical response, dynamic recovery and recrystallization during the process of severe plastic deformation. Two kinds of constitutive models will be introduced in this paper, because there are few models considering...
Proceedings Article

Fractal dimension characterization for surface microtopography of copper cut by single point diamond tool

Yang Yang, Gang Wang, Tingting Zhou, Maobing Shuai
Single point diamond turning is one of the key technologies among modern ultra-precision machining. The finished surface roughness is nanoscale. It shows that the copper surface cut by single point diamond tool exhibits tool marks as well as grain concavity and convexity under different cutting parameters....
Proceedings Article

Study on Effect of Storage Time on Oxidation Induction Time of HDPE

Yun Cheng, Xiaoli Zhao, Weijun Zhong, Yanfeng Yang
The performance of high density polyethylene products during storage will decline because of the aging of materials. The oxidation induction time is an important performance to reflect the oxidation resistance characterize of the material. The oxidation induction time of the samples during different...
Proceedings Article

Study on the Reliability Evaluation of Typical Light Electric Aircraft

Xingbai Zhang, Qingmin Si, Lei Tian, Gongxin Yu, Xueying Jiang
The reliability level of electric light aircraft is the core index of judging the safety level of its flight. In this paper, the theory and method of reliability determination of Rui-Xiang electric aircraft are studied from the perspective of intrinsic safety. On the basis of Extensive research and data...
Proceedings Article

Study on a Soaking Process of Nitroguanidine Propellant

Xuan Zhang, Ming-Lei Chen, Ruo-Ting Xing, Bo Zhang, Na Wang, Ling-Di Li, Hui Chao, Jun-Wei Sun
In order to increase the surface area of the Nitroguanidine triple-base propellant, and to improve the initial burning rate, lower ignition limit pressure, through a combination of propellant specific characteristics, to determine the appropriate soaking process, to make the surface of the propellant...
Proceedings Article

Experimental Study on a Triple-base Propellant Formulation

Ming-Lei Chen, Xiao Ma, Kai-Lun Xiang, Ruo-Ting Xing, Wen-Bin Liu, Bo Zhang, Na Wang, Dan-Dan Ji
In order to optimize the triple-base propellant's preparation technology and improve the combustion performance, used the half solvent method to prepare a series of propellant samples with different solvent ratios, and used the close bomb experiment and scanning electron microscope (SEM) and other experiments...
Proceedings Article

Deflection Design of Joinery Melamine Shelf in Cabinet Furniture

Yun Liu, Shuang Shi, Liming Sheng
The center point deflection of melamine veneer joinery shelf is calculated through orthogonal isotropic deflection equation, and is verified on the basis of the experiment. Then, the calculation formula of the deflection value of melamine veneer joinery shelf that satisfies the practical production is...
Proceedings Article

the Application of SiC in Converter Steelmaking

Hailing Li, Qichun Peng, Youhua Wang
Silicon carbide has better deoxidization ability than ferrosilicon and recarburizer by the thermodynamic analysis,the gas of CO produed by the deoxidation reaction can agitates molten steel which could purify the molten steel .In this article, we choose HRB400 as our testing steel,it is found that the...
Proceedings Article

Design and Research of Marine Non-thermal Plasma Reactor

Jiang Lei, Sun Wei
This paper introduces a new technology of exhaust treatment: dielectric barrier discharge plasma technology. Non-thermal plasma (NTP) has been studied as a potential candidate for diesel engine exhaust after-treatment, and the NTP reactor was the critical component in the technology. Research shows that,...
Proceedings Article

Review of Estimation on Vertex Normal Vector and Discrete Curvature of Triangular Mesh

Ting Wu, Libing Zhang
In order to reconstruct the gingival margin curve of the discrete curvature estimation of triangular mesh surfaces, the estimation methods of the vertex normal vector and discrete curvature of the triangular mesh model are summarized and reviewed. By the analysis of the existing method of vertex normal...
Proceedings Article

A design of hexapod robot control system based on 430 MCU

Yi Fu, Ling Long, Dajun Guo
This paper presents a new multi-functional hexapod robot control system. The basic framework includes the steering gears and the brackets, the wireless controller remotes signal to the main control board, and servo control board outputs multiplex PWM waves to respectively control steering gears. Front-facing...
Proceedings Article

Effect of danling chain content on properties of 10-undecenoic acid-based polyurethane

Bin Cui, Changqing Fu
A new linear 10-undecenoic acid-based diol and a chain extenders with 12C dangling chain length were synthesized via thiol-ene coupling and esterification reaction. In order to investigate the effect of the 10-undecenoic acid-based diol chain extender, the mole percent of the 10-undecenoic acid-based...
Proceedings Article

Research on mobile robot navigation based on Kinect depth information

Lizong Lin, Hao Zhang, Yajun Xu, Changxian Zhang, Shuang Liu
This paper presents a method of mobile robot navigation based on the Kinect. The proposed method has advantages of flexibility and low cost compared with the traditional sensors, such as laser scanner. Using the Kinect depth information, the SLAM and path planning are realized and the mobile robot navigation...
Proceedings Article

Identification and Solvent Extraction-Sedimentation Removal of Metallic Elements in Coal Tar Pitch

Lijuan Gao, Xiaojun Zheng, Yaming Zhu, Xuefe Zhao
Refined pitches were obtained by distillation and solvent extraction with raw materials of the high temperature coal tar and medium-temperature pitch, respectively. Modified pitches were achieved by air oxidation treatment of refined pitches. Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES)...
Proceedings Article

Research on xBOM model for supporting product collaborative innovation

Yi-Ying Zhang, Xiao-Bing Liu, Wei Mu, Hong-Guang Bo
With the increasingly fierce competition among manufacturing enterprises, collaborative innovation of the products is very important. By defining the virtual part, intermediate part, outsourcing part and the relevant mapping function, it is realized that the Engineering BOM(EBOM) and Process planning...
Proceedings Article

Effects of cooling rate on the structural Al-p+ layer for n-type silicon solar cell

Xianfeng Feng, Chang Liu
In this paper, we have made a simple Al-p+ layer on n-type silicon wafers with a commercially available aluminum paste, screen-printing and traditional annealing furnace. The influences of firing cooling rate on the structure and thickness of Al-Si recrystalline layer are discussed. By changing the cooling...
Proceedings Article

Raman scattering properties of structural defects in SiC

Xianfeng Feng, Yuan Zang
Although silicon carbide crystals have been commercially available, the structural discontinuity in crystal always leads to complex interplay between the atomic positions and the electronic structures, hence results in the crystal reconstructing structurally and electronically. Here we investigate the...
Proceedings Article

Numerical Simulation on Erosion of Drain Valve

Liangliang Xu, Zhengdong Wang, Xinhai Yu, Cong Zeng
In this paper, numerical simulations on Y-type drain valve were carried out using Eulerian-Lagrangian model. The simulation results were verified by the experimental ones. It was found that the droplet velocity close to the sealing surface exceeds the threshold values, resulting in serious erosion. To...
Proceedings Article

The application of Industrial machine vision detection and location technology in car key assembly equipment

Li Ye, Bin Luo, Janghua Yang
This paper introduces the auto wireless automatic assembly system, an automatic assembly equipment. Present domestic car keys assembly way is mainly manual assembly. Manual assembly production efficiency is low, the intensity of labor is big, high cost. In order to change this way of backward manual...
Proceedings Article

A Research on the Dispersion Stability of Aligned Carbon Nanotubes

Xiao-Ning Liang, Wei Li
The alignment of carbon nanotubes in composite materials can make the materials anisotropic. This characteristic has drawn a lot of attention recently. This paper examined the stability properties and working lifetime of carbon nanotube suspensions containing highly aligned multi-walled carbon nanotube...
Proceedings Article

Research on Resistance Characteristics of Axial Breather with Tangential Air Inlet

Qijun Wang, Rangshu Xu, Zhe Dong, Ning Ge
By calculating fluid dynamics (CFD), the flow field of several shaft center breathers in different structure has been researched in detailed. Computational domain is simplified according to the actual requirement. RSM turbulent model is used to simulate the strongly swirling turbulent flow field of the...
Proceedings Article

The Numerical Simulation of the Interior Flow of a Dual Orifice Centrifugal Nozzle

Qijun Wang, Rangshu Xu, Ning Ge, Zhe Dong
This paper attempts to research on a dual orifice centrifugal nozzle of a certain aero-engine using CFD method to numerically simulate the interior flow, which will provide reference for design. The computing models for the primary fuel line and the secondary fuel line of the nozzle are built separately....
Proceedings Article

Education management and technology reform in big data era - a new paradigm

Xuejian Mo
With the development of cloud computing and mobile Internet, big data in various fields quickly became a hot topic in education, big data is becoming a disruptive innovation to promote the education system and change the power of science. Starting from the big data features, educational management era...
Proceedings Article

A Study of the Electronic Social Commerce Model as Based on Campus Witkey Networks

Qiongwei Ye, Qian Zhang, Nangai Yang, Yumei Luo
Thanks to the popularity of internet plus and the rapid development of social networks, the Witkey model has become an important element of the electronic social commerce that meets the multi-level and multi-dimensional needs of people by a full integration of the O2O model and the SoLoMo model. Through...
Proceedings Article

Hidden Space Smooth Support Vector Machine with C Means Clustering

Jinjin Liang, Wenhao Xie, Xiaoyan Wang
A piecewise smooth model is proposed and called HSSSVM-CM for short in the hidden space. Mapping the training data to the hidden space with a hidden function, HSSSVM-CM divides the original data into several subclasses by C means; derives the smooth differentiable unconstrained model by utilizing the...
Proceedings Article

An improved ICP algorithm based on Generalized Procrustes Analysis

Wei Wei Tian, Cheng Jun Tian, Lei Han
Point cloud registration often use ICP algorithm to match ,which is the classic algorithm of point cloud registration, due to the presence of some defects in ICP algorithm, scholars later have done a lot of improvements. In this paper, we firstly view the traditional ICP algorithms, then we propose the...