Proceedings of the 2015 Joint International Mechanical, Electronic and Information Technology Conference
Session: Electronics and Electrical Engineering
41 articles
Proceedings Article
Research on high density SMT reliability of aerospace products
Xuming Liu, Baiyang Cao, Yin Xu, Ran Xiao, Hailong Zhao
High density assembly of aerospace electronics equipment is an important direction of research linking technology. Based on the experiment, the paper complete the solder of high density aerospace products under different welding parameters , including PBGA and CBGA in different sizes. Secondly, execute...
Proceedings Article
Power Cable Structure Recovery and Application Based on Mould Melt Joint
Haijie Zhong, Yunjie Xia, Jinming Wang, Hong Huang, Zhenjie Liang
Many failures of power cable system expose that power cable accessories are the main weak point because of frequently poor workmanship and low-quality when installed on-site. That introduces a question that could we use another method to reduce power cable accessories failures rate. Mould Melt Joint...
Proceedings Article
Radar Downstream Channel Phase Noise Measurement and Analysis
Rui Xu, Jianhong Xu, Xinfeng Fan
The channel system parameter of phase noise has an important influence on the performance of the radar receiver. With a brief introduction to the concept and formation mechanism of phase noise, the research was focused on local oscillator phase noise, which has the greatest impact on the performance...
Proceedings Article
Theory and Experiments of a Rolling-ball Mechanism for Horizontal Vibration Isolation
Gaofeng Guan, Qiang Yu, Fei Shen
It’s significant to isolate micro-vibration interference from ground to precision instruments, so lots of scholars have paid attention to study vibration isolation mechanisms and got a fruitful outcome. The most important characteristics of a passive vertical vibration isolator are natural frequency...
Proceedings Article
Study on underwater connector temperature and pressure testing technology
Jun Liu, Yuchen Wang, Baoshuang Shi, Daoming Wang, Liquan Wang, Xiangjuan Xu
the paper has researched the relevant authority standards of domestic and international such as ISO 10423, ISO 13628, API SEPC 17D, ISO 13679, ISO 21329, API Spec 6A, then determined the designed parameters of the temperature pressure test connector. And, the test device was designed according to the...
Proceedings Article
Z-domain Analysis about the Impact of Op-Amp FDCG, NLDCG, GBW and SR on Performance of Switched-Capacitor Integrator
Hong-wei Ma, Jian-hui Wu
The corresponding variation form of the Z-domain transfer function of switched -capacitor integrator(behavioral simulation model) under the impact of op-amp’s four nonlinearities are explored in detail in this paper, which are finite direct-current gain(FDCG), nonlinear direct-current gain(NLDCG), slew...
Proceedings Article
Research of Quality Management Method Based on Power Big Data
Nige Li, Min Xu, Jie Fan, Wantian Cao
Power big data is big data concepts, technologies and methods practiced in the power industry. Power big data related to electricity generation, transmission, substation, distribution, electricity, dispatching the links, cross-unit, multi-disciplinary, cross-business data analysis and mining. Big data...
Proceedings Article
Risk-based information security audit applied research in the power industry
Gengshen Yu, Qian Guo
This paper analyzes the information security situation in the power industry,Combined with information security requirements of the power industry, From the information security audit objectives, audit evidence, information security control framework, information security and other aspects of the audit...
Proceedings Article
Embedded System Design in Closed-loop Active Flow Control
Qiyang Hu, Naiming Wu, Jia Ren, Chang Liu
Closed-loop active flow control in this paper is applied in S-shaped inlet to enhance engine intake quality for the sake of the inlet’s special structure. The pressure coefficient gradient is used to reflect the degree of controlling flow reattachment on the S-shaped inlet. A transfer function is established...
Proceedings Article
Research of Vehicle Electrical Fire Authentication Based on Metallographic Analysis
Gu Yangyang, Xi Ming, Wang Zheng
Vehicle electrical fires mostly are caused by the circuit fault, analyze the circuit molten marks by using the metallographic analysis to determine the circuit molten marks belongs to the primary or secondary molten marks is a important method for vehicle electrical fire authentication.
Proceedings Article
The Analysis of the Impact of Master Station's Performance and Mechanism on the Success Rate of Electricity Usage Information Collection
Shuang Gao, Gangjun Gong, Baogang Zhang, Wanqing Yang
Electricity usage information collection system includes a master station system, communication channel and terminal devices. Among them, the master station system is the brain center of electricity information collection system which can achieve called measuring mechanism storage, calculation and analysis,...
Proceedings Article
Compact Dual-frequency and Dual-polarized Monopole Antenna
Kang Luo, Bin Chen, Yigang Wang, Boao Xu, Xiaoli Zhou
In this letter, a compact dual band monopole antenna with circularly polarized ( CP ) property around 2.4 GHz and linearly polarized ( LP ) property around 1.57 GHz is presented. The antenna consists of a tree-shaped monopole antenna and a modified grounded plane. To realize CP characteristic, two orthogonal...
Proceedings Article
Research on the Deformation Measurement of Ground Collapse Based on Spiral Parallel Cable and TDR
Bo Cao, Qing Li, Yangkai Zhang
This paper briefly describes the defects of the ground collapse measurement technology at present and proposes a new method for measuring the ground collapse. The structure of the spiral parallel cable is illustrated and its circuit characteristics are deduced,it is concluded that the characteristic...
Proceedings Article
The design of the RF radio signal acquisition and analysis system
Gaojian Zhang, Gang Yang, Lin Yang, Qingqing Zhang
A RF radio signal acquisition and analysis system which is based on ARM and FPGA hardware architecture is designed in the paper. The system can measure the field strength data of multiple frequency radio signals at the same time, and save the demodulation broadcasting audio in real time. In addition,...
Proceedings Article
Design of multi-channel automatic switch high precision low voltage change-over switch
Bing Zhou, Jing Hui Zhao
There is a kind of multi-channel automatic switch high precision low voltage switch. The conversion axis of low potential automatic change-over switch has public contact. The public contact and indexing plate’s each indexing position contact constitute the multi-channel change-over switch. Stepper motor...
Proceedings Article
Design of Embedded Numerical Control System Based on ARM
Dongdong Li, Zhiqin Wei
The emergence of embedded technology brought a new technological revolution for the field of modern industrial numerical control. Based on the analysis of embedded technology and computer numerical control systems, this paper discussed the general structure model of embedded numerical control system,...
Proceedings Article
Optimization Analysis of Cooling Process of 3D-Printing in FDM
Li Yanxiang, Cao Guangchun, Xie Lu, Huang Dahai
Fused deposition modeling (FDM) has brought great innovation for manufacturing because of its simple processing and forming rapidly, but the printing products created by this way are always found low-strength, deformed, cracked and so on. Aiming at these problems, there have been many researches on the...
Proceedings Article
Studies on Transmission Network Planning Methods with the Comprehensive Effect of Uncertain Factors
Li Hua, Jin Shixin, Li Wei, Zhang Zixin, Zhao Lin
The uncertainty of wind power, illustrates that the uncertainty of load and wind power have a great impact on the transmission network planning results. In order to obtain more stable and reasonable plan, the transmission network planning which considering the combined effect of wind power and load is...
Proceedings Article
Fault Tolerant Control of Quadrotor based on Parameter Estimation Techniques and Reconfigurable PID Controller
He Xie, Jean-Charles Chaudemar, Huang Jun, François Defay
This paper focuses on the fault tolerant control of quadrotor. In this paper, the dynamic model of quadrotor and its measurements model will be given, and a PID controller will be designed based on the models. Then we propose an approach to detect and diagnose the fault of rotor with the help of parameter...
Proceedings Article
A 14-bit 2.5 GS/s DAC based on Multi-Clock Synchronization
Hegang Hou, Zongmin Wang, Ying Kong, Xinmang Peng, Haitao Guan
This paper presents a 14-bit 2.5GS/s current-steering segmented DAC with a new technology of synchronization, called multi-clock synchronization, which is used to optimize the timing between the internal digital and analog domains. The quad-switch architecture is also adopted to mask the code-dependent...
Proceedings Article
The transmission characteristics of the laser pulse in cumulus
Hongxia Wang, Qinghua Zhang, Aijun Li
The transmission of laser beams in dense medium like cumulus will produce multiple scattering phenomena. The results of multiple scattering not only weaken the laser energy, but also lead to the broadening of laser pulse in time domain. In this paper, the scattering parameters of cumulus were calculated...
Proceedings Article
The High frequency induction electric iron Design of adjustable and constant temperature
Qiang Song, Jianguo Song, Pengtao Mu
The method which adopts the XMC1300 of infineon as the master control chip, using armored K type thermocouple temperature acquisition, after XMC1300 A/D conversion of the improved PID algorithm control source system of constant temperature;To improve the traditional low frequency resistance wire of electric...
Proceedings Article
Sensor Optimization Selection Based on Fault Detectability and Trackability
Luo Jianlu, Tan Xiaodong
Correctly selecting and reasonably arranging sensors are critical to high fidelity health assessment and low testing costs. A novel approach of sensor optimization placement for health monitoring based on fault detectability and trackability is proposed in this paper. Firstly, the requirements of sensor...
Proceedings Article
A yaw angle testing system design based on magnetoresistive sensor and accelerometer
Ping Xia, Yangkui Xiang, Fuyong Cheng
With the development of aerospace business and the popularization of automobile and yacht, navigation has been an important part of people’s life. And in the area of navigation, obtaining of yaw angle appears especially important. This paper designed a electronic compass with angle compensation used...
Proceedings Article
Multi-Parameter Fluctuation Effects on InGaAsP/InP Geiger-Mode Avalanche Photodiodes
Qian Dai, Jie Deng, Zhu Shi, Li-bo Yu, Hai-zhi Song
For Geiger-mode avalanche photodiodes, a statistical method is advanced to establish the quantitative correlation between the controllability of structure parameters and the homogeneity of device properties. Setting many parameters fluctuating independently and simultaneously, the collective effect of...
Proceedings Article
The Experimental Study of Mine Intrinsically Safe Electromagnet
Li Jing, Zhang Xi, Li Zhi
Electromagnet, as the actuator of electro hydraulic control system, its performance directly affects the performance of the electro-hydraulic control system. This paper analyses the working principle of intrinsically safe electromagnet, determines the experimental program, and tests the characteristics...
Proceedings Article
Accurate source localization approach based on illuminating LEDs in indoor environment
Yan Zhang, Xiansheng Guo, Ya Zhou
We propose a new positioning system based on the received signal strength (RSS) fingerprinting approach. The RSSs of LEDs are influenced by some ambient parameters, such as radiation pattern, incidence angle, attenuation coefficient, multipath fading and so on. And these factors degrade the performance...
Proceedings Article
The comparative study of equal channel angle and step angle of the buckle battery sealing concave film
Wenhuan Gao, Huilai Sun
Based on the 3D modeling of closing machine by SolidWorks, the sealing process of button battery is mainly analyzed and comparative study on equal channel angular sealing concave film and the sealing step angle concave film are studied with the contact stress with battery with the change of time. In...
Proceedings Article
Dynamic Analysis For Power Amplifier Electronic Equipment
Famao Wu, Long Jiang, Jian Wang, Weibing Zhu
Power amplifier electronic equipment is an important component of aviation weapon system, and random vibration is a main factor result in structural failure. In order to fully understand dynamic characteristics of power amplifier electronic equipment, according to modal analysis theory, the theory of...
Proceedings Article
Six-phase Fuzzy Control of City Single-cross Road
Dewei Zhang
This paper discusses city single-cross road’s traffic light real-control. Considering the pedestrians and non-motor vehicles, we carry on the six phase fuzzy control. It present a method of current phase green light delay , set up the algorithm and 3D controller design method. It also set up the principle...
Proceedings Article
Achieve Fuzzing Based on Symbolic Execution Platform
He Hao, Gan Shuitao
The traditional software development does not consider the concerns, which is can addressing security problem effectively. So how to find the problem is the standard consideration for security researchers. In the field of software security testing, there are four ways, Fuzzing, Dynamic Taint Analysis,...
Proceedings Article
Research on Hybrid Temperature Measurement Method for High Speed Motorized Spindle
Li-xiu Zhang, Jin-peng Li, Chao-qun Li
Temperature measuring method is one of the key issues in the research of high speed motorized spindle of thermal characteristics.In this paper, a new hybrid temperature measurement method is proposed, which is based on the contacted temperature measurement and infrared temperature measurement experiments,...
Proceedings Article
A High Energy Resolution X-ray Spectrometer using SDD
Chen Er Lei, Feng Chang qing, Ye Chun feng, Liu Shu bin
A high energy resolution X-ray spectrometer based on Silicon Drift Detector is described in this paper. The spectrometer consists of the SDD detector module, the analog electronics for shaping and filtering and the digital electronics for peak detection and data transfer. The system can working at room...
Proceedings Article
Study on Weighting Method of Functions and Performance Indicator System of IETM Authoring System
Xu Zongchang, Hu Chunyang, Sun Hanbing
IETM authoring system is the important instrument to make IETM. Studying its indicator system helps choosing them. This paper introduces overviews of the indication system, then combining several weighting methods, achieves quantitating weights of functions and performance indicators of IETM authoring...
Proceedings Article
A Signal Transmission Model for Diffusion Based Molecular Communication Nanonetworks
Daniel Nzinga Kinsumuna, D. Turgay Altilar, Deniz Demiray
Nanonetworks is a communication between nanodevices, called nanomachines. Nanomachines are very small devices at the range of 10-9 metre. Molecular communication is one of the types of nanonetworks in which nanomachines are able to sense, calculate, actuate and intercommunicate. Transmission, propagation...
Proceedings Article
Analog Front-end Design of Passive RFID Tags for ISO/IEC 14443 and 15693
Yan Guoqing, Li Xiaojin, Chu Jianpeng
This paper presents a design of analog front-end of passive RFID tags for ISO/IEC 14443 and 15693 by using SMIC 0.18 m 2P4M CMOS process. In order to have better performance, three rectifiers have been designed and compared, LDO and low-pass filter have been designed to obtain a high PSRR and a large...
Proceedings Article
A chopped charge pump of PLL
Pu Luo
In this paper, a chopped charge pump with matching up and down pulses was introduced. The proposed topology is based on differential current sources and sinks. a switching circuit for switching on in a first phase one current source of each pair to provide up current pulses, and switching on in a second...
Proceedings Article
An Improved Design of L-probe Feeding Microstrip Antenna Array for 4G Applications
He Wang, Hu Yang, Lei Gu, Fei Zhao, Wenlu Yi
To meet the high requirements of 4G mobile communication systems, such as broadband, wide beamwidth and high gain, an improved microstrip antenna array fed by L-probe is proposed. Generally, most of the 4G antenna array elements have wide band and a gain of 3-5dBi. But the beamwidth in the horizontal...
Proceedings Article
Research of WeChat Public Number's Security of Power Information System
Gao Peng, Shi Cong-cong, Fan Jie
With the popularization and development of mobile Internet and smart mobile terminals, the WeChat public number which combines traditional services and mobile internet application has become the development require of power information systems, research for the security of WeChat public number of power...
Proceedings Article
Influence factors and Countermeasures of breaker’s shunt capacitor dielectric loss measurement
Yang Junting, Peng Peng, Yang Zhaoguang, Wen Dingjun
Affected by various factors, the result of shunt capacitor of breaker dielectric loss measurement is easily misjudged. In order to avoid misjudgment, this paper analyzes the common three kinds of influence factors: interference signals in the site, Cardon effect and air humidity. Three methods were proposed...
Proceedings Article
A New High Speed LVDS Repeater
Wang Liao, Chen Su
A LVDS receiver and driver for LVDS repeater are introduced, which can buffer LVDS one channel to four. As a result, the repeater can speeds up to 633Mbps.It is useful in long distance transmission to reduce signal attenuation.