Proceedings of the International Conference of Mechanical Engineering (ICOME-2022)
251 authors
- Rusu, Marian
- A Comparative Approach on Successive vs Simultaneous Drilling
- Sass, Ludmila
- Ellipse’s Versiera – Structure and Kinematics of the Generator Mechanism
- Sass, Ludmila
- Modeling and Simulation of an Orthodontic System of a Real Patient Starting from CBCT Images
- Savu, Danut
- Differential Thermal Analysis in Microwave Hybrid Field of Some Composite Ceramic Materials
- Savu, Dănuț
- Evaluation of Residual Stress In Specific Welded Nodes of River Ships
- Savu, Ionel Danut
- Microwave Heating of Exhaust Systems from Combustion Engines for Improvement of After treatment Systems
- Savu, Ionel Danut
- Analysis of CO₂ Emissions for a Supercharged Engine and a Series–Parallel Hybrid System
- Savu, Sorin
- Evaluation of Residual Stress In Specific Welded Nodes of River Ships
- Savu, Sorin
- Differential Thermal Analysis in Microwave Hybrid Field of Some Composite Ceramic Materials
- Savu, Sorin Vasile
- Microwave Heating of Exhaust Systems from Combustion Engines for Improvement of After treatment Systems
- Savu, Sorin Vasile
- Analysis of CO₂ Emissions for a Supercharged Engine and a Series–Parallel Hybrid System
- Scurt, Florin Bogdan
- Study of Heat Transfer in the Walls of the Body Superstructure of a Vehicle for Transporting Frozen Meat Carcasses
- Stan, Răzvan Sabin
- Navigation Testing Procedures for the ENDORO Robotic System
- Stanasel, Iulian
- Study of Heat Transfer in the Walls of the Body Superstructure of a Vehicle for Transporting Frozen Meat Carcasses
- Stefan, Iulian
- Microwave Heating of Exhaust Systems from Combustion Engines for Improvement of After treatment Systems
- Stefan, Iulian
- Analysis of CO₂ Emissions for a Supercharged Engine and a Series–Parallel Hybrid System
- Stefan, Iulian
- Differential Thermal Analysis in Microwave Hybrid Field of Some Composite Ceramic Materials
- Stăncuț, Eugenia
- Studies on the Influence of Process Technological Parameters on Geometric Accuracy in 3D Printing of PLA Parts by FFF Printing Technology
- Stăncuț, Eugenia
- Study of the Stop Phenomena at the End Sliding Plate Movement with Reciprocating Rectilinear Motion Driven by Direct Current Motors
- Tarnita, Daniela
- Stresses in Prosthetic Elbow Joint During Flexion-Extension Movement
- Tarnita, Daniela
- A Personalized Three-Dimensional Model of a Patient Using CT Images
- Tarnita, Daniela
- Modeling and Simulation of an Orthodontic System of a Real Patient Starting from CBCT Images
- Tarnita, Daniela
- Study of the Influence of Speed and Type of Roads on Vibrations Transmitted to an Electric Tractor Driver
- Tarnita, Danut-Nicolae
- Stresses in Prosthetic Elbow Joint During Flexion-Extension Movement
- Ting, Jonathan
- Analyzing Double Pendulum Dynamics with Approximate Entropy and Maximal Lyapunov Exponent
- Tolea, Bogdan Adrian
- Study of Heat Transfer in the Walls of the Body Superstructure of a Vehicle for Transporting Frozen Meat Carcasses
- Toma, Marius
- Research Regarding of the Autonomy of the Electric Vehicles in WLTC Test Cycle
- Trasca, Eugenia
- Pollution Caused by Thermal Engines When Using Biofuels
- Trasca, Eugenia
- The Influence of Sliding Pressure Operation on Some Elements of the Thermal Cycle
- Trasca, Eugenia
- Evaluation Methods of Energy Performances in Buildings
- Trif, Andreea Gabriela
- The Link Between Historical Research and Structural Rehabilitation in the Case of Palace Building from Craiova
- Trif, Andreea Gabriela
- Strategy for Facade Restoration in Case of Craiova’s City Hall Building
- Trotea, Mario
- Determination of the Probability of Failure of the Starter of a Passenger Car
- Trotea, Mario
- Influence of Damping Coefficient Value of Fluid Viscous Damperson Seism Behavior of a Ten Stories Building Using ETABS Software
- Truşcă, Daniel Dragoş
- Night-Time Experiments on Driving RHD Vehicles in LHD Traffic Conditions and Pedestrian Crossing Safety
- Tutunea, Dragos
- Pollution Caused by Thermal Engines When Using Biofuels
- Tutunea, Dragos
- Experimental Stand to Investigate the Sealing Properties of Piston Rings Used in Automotive Industry
- Tutunea, Dragos
- The Influence of Sliding Pressure Operation on Some Elements of the Thermal Cycle
- Tutunea, Dragoş
- Comparative Analysis of Pedestrian Throwing Distance Following a Collision with a Vehicle
- Udriștoiu, Anca Loredana
- Navigation Testing Procedures for the ENDORO Robotic System
- Vintila, Daniela
- A Personalized Three-Dimensional Model of a Patient Using CT Images
- Vintila, Daniela
- Modeling and Simulation of an Orthodontic System of a Real Patient Starting from CBCT Images
- Vintilã, Daniela
- Study of the Influence of the Thermal Insulation System on the State of Stress, Deformation and Vibration of a Rehabilitated Building with a Structure of Reinforced Concrete Frames
- Vladu, Cristian
- Design of a Parameterized Mannequin Using Rapid Prototyping Technology
- Vladu, Cristian
- Experimental Approaches Regarding a Children Rehabilitation Test Bed
- Voloacă, Ștefan
- Modeling the Characteristics of an Electric Propulsion System for a Small Vehicle
- Ștefan, Iulian
- Evaluation of Residual Stress In Specific Welded Nodes of River Ships
- Țigăneșteanu, Constantin
- Selective Laser Sintering of Ti Alloy Powders for Hip Implants
- Țoțu, Vlad
- Dynamic Optimization of the Controller for the Active Suspension System of a Race Car
- Ṭãlu, Mihai
- Study of the Influence of the Thermal Insulation System on the State of Stress, Deformation and Vibration of a Rehabilitated Building with a Structure of Reinforced Concrete Frames
- Ṭãlu, Ştefan
- Study of the Influence of the Thermal Insulation System on the State of Stress, Deformation and Vibration of a Rehabilitated Building with a Structure of Reinforced Concrete Frames