Several different Li+-imprinted gels were prepared by different precursors. And the gels were characterized by textual properties and point of zero charges (PZCs). The adsorption of Li+ from their aqueous solutions by the gels was investigated. The surface areas of the gels were found to range from 60...

We investigated the effect of lactoalbumin on the processing properties of vulcanized rubber by adding lactoalbumin protein. We found that G’ and G’’ of vulcanized rubber were increased and tan was decreased by adding lactoalbumin. The addition of lactoalbumin can improve the processing properties of...

Ammonia and HTT were compounded and tested as a novel preservative system for concentrated natural rubber latex (CNRL) to replace traditional preservatives. The preservation effects and the viscosity of prevulcanized CNRL were measured. After preservation treatment, the drying characteristics, the mechanical...

The water polluters of Liao river basin in Jinzhou is elected preliminarily basing on the basin of the key water polluters of Jinzhou city, combining with the principle of polluters screening and the computing method of equal standard pollution load, optimizing and assessing the indexes which involves...

The present study reports that a modified coaxial electrospinning process, which was successfully carried out to control the diameters of shellac fibers. With a Triton-X100 in ethanol as sheath working solution and shellac ethanol solution as a core electrospinnable fluid, the coaxial electrospinning...

Physical, chemical and mechanical properties of some abrasives such as diamond, CBN are described in this paper. The preparation and application of ultra-hard oilstones such as diamond and CBN are also discussed. They are widely applied in honing and promote great development of honing technology. However,...

A soft bulletproof layer is made by utilization of the newest domestic Ultra high molecular weight polyethylene fiber, and by composing float-assisting and puncture-proof functions, multifunctional float-assisting, bulletproof, puncture-proof composite clothes is developed, according to the current flaws...

Colored non-slip surface coating has an important role in the prevention of traffic accidents and obtains more and more attention and application. This paper based on chemical reaction principle of poly methyl methacrylate with a curing agent to produce a fast secondary crosslinking reaction coating...

Epoxy/graphene nanoplatelets(EP/GNs) composite was prepared by ball milling(BM), using diglycidyl ether of bisphenol A(DGEBA)as matrix, Diethyltoluene diamine(DETDA) as curing agent, GNs as thermal conductive filler. The mechanisms and influence of different BM time to exfoliate layered GNs and compound...

According to the problem that the quality assurance of acrylic is not reliable, we use the Michelson interferometer theory to build a Spectral-Domain Optical Coherence Tomography system composed by reference arm, sample arm and spectrometer. Obtaining the 2D and 3D pictures, then measuring the thickness...

Volatile phenols are a class of protoplasmic toxicants which have caused inevitable environmental problems in many sea areas. This paper analyzed the content, pollution level and distribution of volatile phenol in bottom waters Jiaozhou Bay in May, September and October 1983. Results showed volatile...

This paper analyzed the contents, distributions and pollution sources of As in Jiaozhou Bay waters in 1983. Results showed As contents ranged from 0.19-4.89 g L-1,in the whole year, and were lower than Class I for As (20.00 g L-1) in National Standard of China for Seawater Quality (GB3097-1997). There...

We analyzed the spatial distributions and seasonal variations of volatile phenols in the bay mouth of Jiaozhou Bay in May, September and October in 1983. Results showed that volatile phenols contents were changing by means of vertical water’s effect. Volatile phenols contents in surface waters were in...

This paper analyzed the content and distribution of Arsenic (As) in bottom waters in the bay mouth of Jiaozhou Bay in May, September and October 1983. Results showed As contents ranged from 0.15-2.30 g L-1 in bottom waters in the whole year, and were more lower than Class I for As (20.00 g L-1) in National...

Based on the investigation data on Cu contents in different seasons in 1983 in surface waters in Jiaozhou Bay, we analyzed the contents, pollution level and distributions of Cu. Results showed that Cu contents in May, September and October were 2.47-20.60 g L-1, 0.86-4.86 g L-1 and 0.77-3.00 g L-1, respectively....

Based on the investigation data on As in surface and bottom waters in the bay mouth of Jiaozhou Bay in 1983, this paper analyzed the seasonal variations, vertical variations and horizontal distributions of As. Results showed that As contents in surface waters in different seasons were in order of summer...

Perovskite-type cube structure LaMnO3 nanofibers of approximately 50~100 nm in diameter were synthesized via Sol-Gel processing and electrospinning technology after calcined at 900 by using polyvinypyrrolidone (10 wt %PVP) as complexing agents. The nanofibers was characterized by means of scanning electron...

In this article, curve fitting is conducted on the original data of aluminum alloy via matlab. Then, to find out a fitting curve with optimal effect, comprehensive analysis is made on the judgement quantitative index of curve fitting. The wire feed rate of other given current is obtained with such fitting...

Osteopontin (OPN), as a malignant transformation related protein phosphorylation was firstly completed the extraction by Senger in 1979. With the progress of research on osteopontin (OPN), people found out that there was little amount in the normal tissues that was showed with low expression, however,...

Osteopontin (OPN) is a kind of phosphorylated acidic glycoprotein, human beings' osteoclasts, macrophages, T cells, and vascular smooth muscle cells can secrete OPN, the gene is located on chromosome 4q13. OPN has a function of adhesion to protein, which can be combined with CD44, integrin v 3 and v...

In this work, alloy coatings with different Al and Mg content have been prepared on overhead ground wires for Zn-Al-Mg series hot-dip coatings providing good protection on mild steel surface against corrosion. A reinforced thermal stability is confirmed by DSC thermodynamic curves. Furthermore, the enhanced...

With the great progress of hemoglobin-based blood substitutes, however, they all have a same problem that is hard to get effective stable structure of hemoglobin. The hemoglobin can be oxidized into met hemoglobin in the process of purification, lead to the loss of the function of carrying and transporting...

In EDM, especially in small holes EDM machining, there will be a lot of debris produced which is difficult to remove from narrow gap. If the debris can’t be removed in time, it will affect the machining accuracy and efficiency, and sometimes even unable to complete the processing. In this paper, the...

Latest surface modification methods of nanoparticles are researched in this article. The mechanism, characteristics and process of surface physical modification methods of nanoparticles such as surfactant and surface deposition are analyzed. The characteristics, mechanism and chemical reaction process...

In this paper, the effects of Ce addition on extrusion alloy phase and mechanical properties of extruded ZM21 magnesium alloy were investigated by the use of XRD, SEM and tensile test at room temperature et al. Analysis of the cerium magnesium alloy extrusion of ZM21 influence of alloy phase and mechanical...

In order to develop non-linear material used for the reinforced insulation in HVDC cable accessory, non-linear EPDM composites were fabricated by adding conductive nano fillers to improve the conductivity characteristic of EPDM. The conductivity and the DC breakdown strength of composites were tested...

This template explains and demonstrates how to prepare your camera-ready paper for Trans Tech Publications. The best is to read these instructions and follow the outline of this text. Please make the page settings of your word processor to A4 format (21 x 29,7 cm or 8 x 11 inches); with the margins:...

Previous studies have shown that: the incidence of a wide range of gastrointestinal motility disorders, high frequency, have seriously affected the recovery of athletes training and after training. This article from a variety of factors that affect gastrointestinal function point of view, its comprehensive...

Porous photocatalytic titania film co-doped with Fe and Si was fabricated on carbon steel substrate by plasma electrolytic oxidation (PEO). The microstructure of the film was investigated and the photocatalytic activity of the film was tested by measuring the photodegradation rate of the organic methylene...

Micro arc oxidation (MAO) coating was first fabricated on AZ91 biomedical magnesium alloy and followed by surface laser treating. Effects of laser treating on surface characteristics of MAO coating were studied. The results indicated that after surface laser treating, the micro pores on MAO coating surface...

It is highly important to choose suitable of the foundation in underground engineering. With the engineering, the foundation is made of gravelly soil, which distributed discontinuity and had bad uniformity. Drilling method, dynamic sounding method and deep plate loading test were applied, combined with...

Aerial aluminum conductor (ACSR) as the primary overhead lines products, has been running in the field for a long time. The inevitable corrosion will be affected by heavy pollution environment. Salt spray is acknowledged as the natural environment in most demanding of corrosion, which can make the wire...

The polymerization of acrylamide was initiated by complex redox system in aqueous solution.Meanwhile, according to the best experimental craft,we conducted a pilot-scale polymerization of acrylamide.We studied the effects of different pilot experiment intrinsic viscosity of the polymer, dissolution time,...

The ternary cation flocculant P(AM-DMDAAC-DMC) was synthesized by aqueous solution polymerization with raw materials of acrylamide(AM),and dimethyl diallyl ammonium chloride(DMDAAC) and methacryloyloxyethyltrimethyl ammonium chloride(DMC) with the complex redox as initiator.Effects of cationic mononer...

In the health management of battery, cycle life prediction is an essential component. Before battery fail, the End-of-Discharge Voltage (EODV) reduce with the use. This paper proposed a multi-phase degradation model of EODV through failure mechanism analysis to evaluate the degree of degeneration of...

China's corn straw resources are very rich, the development of corn straw application technology industry has become a hot spot. In this paper, the present situation of comprehensive utilization of corn straw in China is summarized, including the utilization of corn straw as fertilizer, feed, raw material,...

Oil shale as the petroleum alternative is widely distributed in China, the total oil shale resources and potential shale oil resources are estimated at 719.937 billion tons and 47.644 billion tons, respectively. Shale oil and gas can be obtained through the pyrolosis of the oil shale. In order to study...

Volatiles, sulfur, nitrogen and other impurity atoms have released in the process of bituminous coal retorting and high-quality Lantan can be obtained. In order to investigate the feasibility of Lantan to combustion as a clean fuel instead of raw coal, this paper selects several representative coals...

In this paper, steel slag powder, slag powder and fly ash mixed with different proportions, equivalent replacement of cement, as concrete admixture, study the effect of the admixture on the performance and mechanical properties of concrete, and through the XRD, SEM, differential thermal and other micro...

Eu3+ doped bismuth silicate phosphors, Bi4Si3O12:xEu3+ (0.01 x 0.08) were prepared via sol-gel route. XRD results show the phase of the synthesized phosphors calcinated at 650 is isostructural with Bi4Si3O12. Under the excitation of 261nm and 393nm, there are some sharp emission peaks of Eu3+ ions centered...

The detection of rail fastener defects is the key to ensure the running safety of high-speed trains. Traditional method is usually be detected rely on train workers who walk along railway lines to find out the potential risks. The method by artificial maintenance is slowly, costly, and dangerous. As...

Fe2O3 nanorods grown on reduced graphite oxide RGO was synthesized via a facile hydrothermal method followed by a heat-treatment process. The Fe2O3 nanorods grown on the RGO has a average diameter of 40 nm, which is smaller than the pure Fe2O3 nanorod. Investigated as an anode material for Li-ion batteries,...

Nano ZnO/graphene composites were prepared by the oxidation of graphite and nano ZnO as the precursors under the condition of water temperature at 120 . The photocatalytic activity of the composite was detected to treat simulated antibiotic wastewater by using the solution of tetracycline hydrochloride...

the upper gastrointestinal bleeding in medical emergency is common in surgery, patients with critical illness, the short time may be life-threatening, nursing staff in addition to actively assist doctors do all kinds of rescue, hemostatic measures should strengthen close observation of the illness, completes...

The diagnosis of breast disease in Europe and other advanced western developed countries were mainly the biopsy technique, which included fine-needle aspiration biopsy for cytological diagnosis and core needle biopsy for histological diagnosis. This two methods could figure out the basic pathological...

The compatibility, stability and the pyrolysis behavior of aluminum based solid-liquid compound fuel were systematically investigated by thermogravimetric analysis (TGA). The compound fuel lost its 30% weight before the temperature rose to 150 . AP decomposed at 210 and lead to 50% weight loss. The reaction...

NGF and its receptor are expressed in multiple nervous system and tumor of the non-nervous system, which also participate in tumor proliferation, differentiation, apoptosis, angiogenesis and other biological behaviors. In this paper, it takes the interpretation of nerve growth factor (NGF) as the breakthrough...

Based on the features of the structure of double-arch permeable rib tunnel and its spatial deformation mechanism, a corresponding construction monitoring and measuring program was demonstrated in this paper. The reasons of the vault slope deformation and cracking which was the main risk during the construction...

The permeable rib double-arch tunnel is a new type structure of tunnel adjacent to mountain, a better way to solve the problems of engineering stability and environmental protection of highway adjacent to mountain in mountains area. For the environmental geological problems of the tunnel adjacent to...

A novel Dual-Base Transistor (DUBAT) having a negative-resistance characteristic is presented. This device contains a lateral p-n-p Bipolar-Junction-Transistor (BJT) and a Hybrid-Mode Transistor, and is fabricated on silicon based 0.5 m CMOS process, compatible with the standard CMOS technology as distinct...

Recent years, with the constant development of social economy and industry estates, the increasing deterioration of natural environment leads to the deterioration of the plants growth environment, which influenced the good and fast growth of plants. Environmental stimulus might lead to the generation...

Despite significant progress in recent years, microbial fuel cells (MFCs) maintain their status as one of the prime unsolved problems in clean energy technology, and their characteristics may not meet the requirements of practical application. Therefore, preparing high-performance anodes is very important...

Paper filter element, widely used in automobile fuel filter, has deficiencies such as short service life and inevitable replacement after blocking. Based on this, the work developed fuel ultra-precision microfiltration technology taking polymer polyethylene as filter material. Meanwhile, it designed...

For liaohe basin metallurgical industry wastewater treatment technology lack of optimization, selection of technical parameters of the lack of rationality ,management of large scale and lack of in the near and specified future date unified combination, existing metallurgical wastewater treatment technology...

Results of 2015 science and technology development project of Xuchang City(No. 1504007),Results of 2015 produce-learn-research project of Xuchang University(No. 2015CXY10,2015007),Results of 2016 Colleges and universities in Henan province key scientific research project.

Wheat washing can remove stone, dampen and clean. It works with the help of water solubility and flushing action to purify the surface of wheat. For the water consumption and pollution of traditional wheat washing machines have become increasingly prominent, a water-saving cleaning technology for wheat...

Cu2ZnSnSe4 thin films were prepared by spin-coating and chemical co-reduction with different heating modes. The phases of obtained samples were characterized by X-ray diffraction (XRD). The size and morphology of the products were observed by scanning electron microscope (SEM). Experimental results show...

In this paper a 33 story precast shear wall structure is analyzed. In order to study the safety of the tall parapet wall the parapet wall is established in the model. Structure analysis software YJK-EP is taken for the elastic-plastic analysis of this precast sheer wall structure, specifically, the whole...

In order to save vehicle weight and protect environment, lightweight materials such as aluminum alloys have been widely used in the automotive industry. As a solid state jointing technique, refill friction stir spot welding (RFSSW) process is expected to apply to join automobile body parts made of aluminum...

The resistivity of graphite electrode is not only an important parameter to reflect the physical characteristics, but also the main technical index of the graphite electrode. In this paper, The independent design and development of the equipment used for measuring resistivity of graphite electrode body...

As a new type of structural material, X-cor sandwich with high specific strength and high specific stiffness effectively improves the through thickness mechanical properties of the foam sandwich and is promised to be used in the field of Aerospace. Through three steps of pultrusion process, insertion...

The higher order crack tip fields for physical weak-discontinuous problem of cylindrical shells are investigated. The crack located at the interface between homogeneous materials and exponential functionally graded materials. The governing equations are derived for homogeneous materials and FGMs regions...

Hydrogen-bonded directed assemblies of one binary co-crystal was validated by single-crystal X-ray diffraction analysis. The supramolecular reaction between symmetric fumaric acid and 1H-benzotriazole produced molecular co-crystal formulated as [(C6H5N3)•(C4H4O4)0.5] in high yields. Compound contains...

One of the most accepted thermal storage system of solar thermal power for balancing energy considers the use of cementitious/concrete materials. We report the preparation of nano-SiO2 optimized aluminate cementitious pastes as thermal storage materials with mass fractions of 0, 5, 10 and 15% Cu powders...

This paper develops the sulfate scale inhibitor WUR-201 for RO using uniform design method, and the results show that the scale inhibition performance of WUR-201 can reach or even exceed that of scale inhibitor Foreign 1#; the scale inhibition ability increases with pH increasing but decreases with temperature...

Fe-based medium manganese alloy coating was fabricated on 42CrMo steel surfaces using a synchronization powder feeding technique by 6 kW IPG laser apparatus. The microstructure and mechanical property were analyzed by X-ray diffractometer (XRD), scanning electron microscope (SEM), microhardness tester...

Rutting, Top-Down cracking and bottom-up cracking are considered as major damage phenomena in pavement structure. In this study, the Drucker-Prager (D-P) criterion is adopted to analyze the pavement structure on Ji-Qing highway. Three dimensional finite element model with double rounds uniform load is...

Compressive tests were performed to homogenized AZ31 magnesium alloy samples to various strains and fracture at room temperature (RT). The microstructure of the samples was observed by optical microscope(OM); the twin types were examined by electron backscattered diffraction (EBSD) technique; and the...

In this work, a series of ternary rare earth complexes were synthesized with salicylidene glycine schiff base (Sal-GlyK) as anion ligand and 2,2'-bipyridine (bipy), l, 10-phenanthroline (phen) as neutral ligand. The antibacterial activities and interactions between calf thymus DNA (ct-DNA) in Tris-HCl...

At present, Selective Catalytic Reduction (SCR) flue gas denitrification process has been widely used in coal power plants in China. Catalyst is the core of SCR denitrification system. Because of the influence of the fly ash, erosion and chemical poisoning, the catalyst activity can be reduced gradually,...

This paper used magnetron sputtering to grow ZnO film on Al2O3 substrate. All the samples were characterized by X-ray diffraction (XRD), atomic force microscope (AFM), ultra-violet spectrometer (UVS) and photoluminescence (PL). Results showed that: the doped ZnO thin films were still had the hexagonal...

A novel nanosphere -Fe2O3/MWCNT composite has been prepared by a simple hydrothermal method. The characterization of morphology and structure of -Fe2O3/MWCNT composite was carried out by scanning electron microscopy, X-ray diffraction and Raman spectroscopy. It is found that MWCNT was well dispersed...

The effect of powdered activated carbon (PAC) particle size in the range of 0.09~0.18mm on the flow field in membrane filtration process was investigated. The SEM images of membrane surface showed that it might cause damage on the membrane surface in membrane filtration system by the addition of PAC....

The semi conductive shield material was prepared by mixing a variety of copolymer and carbon black (CB) with LDPE by melt blending method. In order to study the suppression of semi-conductive shield materials on space charge injection, inorganic nano fillers with different properties were added respectively,...

In this paper, the effects of Ce addition on as-cast and extrusion alloy microstructure of ZM21 Magnesium Alloy were investigated by the use of OM. Analyses the influence of ZM21 magnesium alloy as-cast and regularity and mechanism of the influence of extrusion organization, the results show that rare...

The mesoporous Bi-S-TiO2/ -CD was prepared by an evaporation induced self-assembly (EISA) method and photoinduced self-assembly method, and was characterized by UV-vis diffuse reflectance spectroscopy (UV-vis DRS), X-ray diffraction (XRD), Scanning electron microscopy (SEM), High resolution transmission...

Thermal drying efficiency and odor emission characteristics under different temperature of municipal solid waste (MSW) were studied. The results showed that: water content decreased sharply with disturbance thermal drying mode. The highest peak of total amount of odor was at 600 and the lowest was at...