Proceedings of the 2nd International Conference on Advances in Mechanical Engineering and Industrial Informatics (AMEII 2016)
Session: Session 1: Mechanical Engineering and Manufacturing Technology
61 articles
Proceedings Article
Functional Design on Purchase Quotation System for Machine Element
Ling Tong, LinLin Li, Rui Zhang, Lei Liu
There are many different kinds of machine element, with professional development of industrial production, only a few machine elements needed by factories are for their own production, most are needed to be purchased. Using purchase quotation system for machine element is an effective mean to ensure...
Proceedings Article
Database Design on Mechanical Equipment Operation Management System
Qiu Zheng, Kaiyuan Wu, Chengyan Wu, Lei Liu
Carrying out mechanical equipment operation management can improve the economic efficiency for enterprises, prevent accidents, ensure production safety, and promote the reform of machinery and equipment maintenance system. Using computer system to manage is the necessary requirements for the information...
Proceedings Article
Design of Controller for Metal Linear Expansion Coefficient Tester
Yufei Fu
An intelligent metal linear expansion experimental instrument scheme brings for the existed problems aimed at measurement equipment of metal linear expansion coefficient. System by the processing core STC89C52RC adopts Holzer displacement sensor SS495A to measure displacement of metal bar expansion....
Proceedings Article
Study On The Barycenter Position Of Measurement And Data Processing For Dura-Axle Vehicle
Bo Wang, Yu-ming Nie, Zezhong Yang, Chengqiang Zong, LanXin Geng
Base on measuring principle of barycenter, the authors analyzed influencing factors of barycenter and measured barycenter of one Dura-axle vehicle according to GB/T 12538-2003. The result showed that the height value of barycenter is different when lifting vehicle for smaller angle, so when measuring...
Proceedings Article
Analysis And 0ptimization Of Car Interior Abnormal Noise
Wei Zhang, Shuhuai Liao, Li Liu
This paper introduces the noise transfer function theory overview, After improvement proposed by the suspension of dynamic stiffness to reduce interior noise opinions, In an example of a compact car, We found the front peak problem by Accelerated conditions experimental test , Using the noise transfer...
Proceedings Article
Water Temperature Distribution When We Take a Bath in the Bathtub
YiYing Li
Through the analysis of the water temperature distribution affected by the shape, volume, temperature of the tub and the person, this model finds the reason why it is so difficult to keep an evenly expecting temperature during bathing time. Furthermore, according to the water temperature distribution,...
Proceedings Article
Study on the Heat Dissipation of the Bathtub
YiYing Li
Through the establishment of water on the surface of the heat loss and the bathtub wall heat loss of the two models to analysis heat bath total loss, as the foundation to find a most suitable strategy the person in the bathtub can adopt. Model of heat loss through water surface discuss the heat loss...
Proceedings Article
Structure Design of Self-limiting Hydraulic Cylinder
Zhen-Nan Ren, Ming-Fu Yin
In recent years, characteristic of rocky pressure machines is developing from low-pressure and static to heavy-duty and revolving. In order to make the pressure chamber of rocky press rotate precisely, this paper puts forward to introduce hydraulic cylinder as a support of the workbench, thus satisfying...
Proceedings Article
Simulated Analysis Of Heavy Duty Car Cab Vibration
Xia Feng
Comfort is an important performance index of modern cars, and thus car production enterprises are making every effort to improve the comfort level of cabs. The cab suspension system plays a key role in obstructing the vibration passed from the chassis to the cab. A simulated analysis on the car cab suspension...
Proceedings Article
Trafficability of rigid wheel with bionic lug on sand by 3D DEM
Guifen Zhou, Songsong Ma, Dianlei Han, Gang Luo, Fang Liu, Rui Zhang
Numerical simulation has significant advantage in analyzing the interaction between rigid wheel and lunar soil simulants and designing the lunar vehicle wheel under complex circumstances. The computer aided design software CATIA and 3D Discrete Element Method simulation software PFC3D were combined by...
Proceedings Article
Research on high water temperature of diesel engine and improvement of radiator
Jian Huang
For a water-cooled engine, radiator performance has a direct impact on automobile engine heat dissipation effect, influence the automobile's power performance, economy and reliability. Based on the 6DL engine high temperature problems are investigated, analyzed the reasons of high temperature of the...
Proceedings Article
Warp knitted seamless garment CAD technology aided design
Xiaomei Zhang
With the rapid development of science and technology, the application of the computer is more and more widely, not only brought great convenience to the life, at the same time also prompted some emerging things arises at the historic moment, such as: warp knitted seamless garment, it is the use of computer-aided...
Proceedings Article
Contemporary equipment in enamel process innovation design accessories
Mi Luo
In recent years, with the rapid development of creative industry, fashion bags has become one of the important element in the accessories. Especially for women dress collocation, the choice of luggage is indispensable link. Luggage industry market development prospect of huge potential, bags designer...
Proceedings Article
The design and application of heterogeneous isomorphism traditional batik pattern
Huan Xiong
In collecting on the basis of traditional batiks patterns, the traditional batiks patterns are classified and summarized the composition of traditional batiks patterns in the form of law, law of color, pattern characteristics, cultural connotation, refining traditional batik pattern elements, will be...
Proceedings Article
Research on Application and Practice of Information Management in Automobile Die Manufacturing Industry
Chengquan Lin
In this paper, the information of Internet and enterprise and customer information exchange communication bridge tool, study of the key components of the automobile manufacture of manufacturing applications, and stamping die design and manufacturing, from the six case analysis, mold manufacturing, cost...
Proceedings Article
Study of shuttle griping and releasing device of weft insertion mechanism of rigid rapier loom
Chenwang Yuan, Yingjie Niu, Ge Chen, Zhengning Li
Rigid rapier loom uses rigid rapier to grip the shuttle and do the reciprocating movement to realize weft insertion. To grip and release the shuttle, a complicated mechanism is used. But usually the stability of the mechanism is not good and the installation is complex. According to simulation and experiment,...
Proceedings Article
Warp Tension Detection Method of Carbon Fiber Multilayer Loom
Xi Lu, Jiancheng Yang
The warp tension, which is the let-off mechanism of carbon fiber multilayer loom, for the study object, the article expounds the composition and distribution of tension sensor, and analysis the detection principle of warp tension, thus design a detection scheme of warp tension. In order to solve the...
Proceedings Article
Simulation analysis of helical gears in the gear box of the rolling mill
Qian Ma, Yonggang Xu, Lixin Gao
This paper studies the helical gears in the gear box of cold rolling mill in a steel, using software SolidWorks to make one pair of meshing helical gears a solid model, and import the entity model into ADAMS to creat a virtual prototype model, using IMPACT function to define the contact between gears,...
Proceedings Article
Optimization of Cutting Power Based on Dynamic Cutting Force Model
Lei Fang, Guangrong Yan, Xiangyu Xu, Tao Ding, Genao Zang, Le LIU
The machine output power smoothing has an important significance to improve the efficiency and quality of machining. With the secondary development of cutting geometry simulation software, we have got the geometry cutting parameters, carried out a physical simulation of the whole cutting processing and...
Proceedings Article
The Design and Simulation Analysis of Electromechanical Double Acting Pneumatic Brake Valve
Qinghe Liu, Guanghui Guo, Fufan Qu
With the increasingly severe environmental and energy issues, the application of urban electric buses is more popular, but the battery reserve capacity has restricted the popularity of electric vehicles. Regenerative braking energy recovery system can reduce the energy consumption of the electric vehicle,...
Proceedings Article
The Assist Curve Design for Electric Power Steering System
Qinghe Liu, Weiguang Kong, Tao Li
Three kinds of power curve are analyzed aimed at the sense of strength and steering portability. Thus, we put forward a new design principle based on the existing research. The assist characteristic range is divided into four kinds according to the vehicle speed and steering wheel torque. The simulation...
Proceedings Article
The establishment and Simulation of the dynamic model of the Four rotor aircraft
Wei Wu, Kai Fan Zhao, Qiang Wang
With the development of space technology and mature, four rotor aircraft with its low cost, high performance, unique structure and flight mode and other characteristics, are widely used in military and civil fields. According to the basic characteristics of four rotor aircraft prototype and flight characteristics,...
Proceedings Article
The Research of Wind Turbine Airfoils Aerodynamic Characteristics Effects Based on Numerical Simulation
Chong Meng
With the development of large-scale wind turbine, the limitation of the classical aerodynamic characteristics of wind turbine research methods has become more sophisticated, and the improvement of CFD numerical simulation technology has provided a new research method for wind turbine aerodynamic characteristics....
Proceedings Article
The Cloud Service Framework Oriented Additive Manufacturing
Lei Wang, Yuan Yao, Xiaoming Yang, Dong Chen
This paper proposes a 4-layer device virtualization system framework based on multi peer nodes. First, the different layers of deployment and the operation processes of the system are discussed, then the resource management and the information flow are described. Finally, the interface and task assignment...
Proceedings Article
The present situation of mechanical parameters in the ground test
Jiafeng Zhao, Wei Wang
Ground mechanics is the study of off-road driving machine interaction with the ground in a mechanical discipline, vehicle dynamics and soil mechanics is a goalkeeper of combining the interdisciplinary, involving vehicles, ground and its interaction research of dynamics, etc. Mechanical parameters test...
Proceedings Article
Influence of aging treatment on microstructure and mechanical properties of a new high strength TB17 titanium alloy
Zhe Wang, Xinnan Wang, Guoqiang Shang, Liwei Zhu, Jing Li, Yue Fei, Shuai Tian, Zhishou Zhu
Scanning Electron Microscope (SEM), Transmission Electron Microscope (TEM) and X-Ray Diffraction(XRD)were employed to investigate the influence of heat treatment conditions on microstructure and mechanical properties of a new high strength TB17 titanium alloy at aging temperature from 530øC to 620øC....
Proceedings Article
Modeling Simulation and Experimental Study on Valveless Electro-Hydraulic Servo Steering Device for Ship
Jian Liao, Lin He, Rongwu Xu, Zongbin Chen
The linear model of valveless electro-hydraulic servo steering device neglects the nonlinear factors, especially the factors of the control subsystem, so the quantitative static and dynamic characteristics of the actual system cannot be evaluated accurately. Aiming at the problem, the steering device...
Proceedings Article
The Design of Micro Vacuum Heating Observation Equipment
Changqing Gao, Jianhua Zhang, Chao Ma, Mingyu Wang, Jianmei Li
In order to study the transition of material properties under the environment of high temperature and vacuum, a micro vacuum heating observation equipment was designed. The vacuum system can create the vacuum environment. And the heating system can create the high temperature environment. This equipment...
Proceedings Article
Constraint-Variable Analysis of Time Coupling Constraints in Unit Commitment
Shuai Cao, Zhenglin Yang, Haihua Cheng, Yaxian Zheng, Jian Geng
Constraint-variable correlation is the most important coupling correlation in unit commitment problem. Reasonable arrangements for the correlation will simplify the model complexity, and reduce the calculation time. And minimum on/off time constraint is one of the most complicated time coupling constraints....
Proceedings Article
Optimization design of Subsoiling components
Zhikai Ma, Yongwei Yuan, Jiangtao Liu, Jinggang Yi
This article is based on the subsoiler as the research object. 3D model is established using large finite element analysis software analyze and optimize the structure afterwards. The structure and thickness of the subsoiler have been optimized and the feature parameters have been changed from different...
Proceedings Article
Numerical Study of the acoustic characteristics of the entry diameter gas-liquid coaxial swirling injector
Honghui An, Wansheng Nie
Linear acoustics is adopted to analyze the influence on the entry diameter of the gas inlet orifice on the acoustic damping of the injector. The impedance tube method is used to assess quantitatively damping capacity of entry diameter of the gas inlet in order to find the best structure parameter of...
Proceedings Article
A Method of Plastic Gear Inspection Based on Machine Vision
Jianbiao Ding, Yajun Zhang, Jian Zhuang, Ri Pan
The defect detection of plastic gear is difficult because of its small size, so a method based on machine vision is proposed to inspect plastic gear accurately and quickly. Digital image of plastic gear is collected by CCD camera, and then the image is preprocessed to generate single pixel edge of gear....
Proceedings Article
Odometer Lever Arm Effect Compensation on Strapdown Inertia Navigation System Precise Alignment with Odometer
Zhi-yuan Ma, Zhi-yong Shi
Odometer lever arm effect on strapdown inertia navigation system initial alignment with odometer is studied in this paper. This paper presents an error compensation method of odometer lever arm. In this method, the difference between output velocity by odometer and velocity output by SINS is taken as...
Proceedings Article
Analysis and Research on Radial Stiffness of Main-auxiliary Spring Structure Wheel
Shijie Guo, Bin Song, Jiangang Lv
In order to improve the traditional pneumatic rubber tire performance of puncture-proof, explosion prevention and environment adaptability, a main-auxiliary spring structure wheel was propesed. The new wheel composed base on metal helical spring mutual woven and interwined. By analyzed the system structure,combined...
Proceedings Article
Study on acoustic and aerodynamic performance of reactive muffler
Zhenyu Deng, Junchuan Niu, Fusheng Sui
In order to get a further reduction on pressure loss of a reactive muffler, the interior flow field of the muffler and the generation mechanism of pressure loss are investigated by the CFD method. Then, the influences of the insert tube length on the acoustic and aerodynamic performance of the expansion...
Proceedings Article
Optimization of Cutting Interference Machining for Aircraft Roller Bearing Formation
Bin Zhang, We Cheng
In the complex components of aircraft roller bearing forming process, it is influenced by the surface mesh inducing factors, resulting in processing accuracy is not good, the error is large. An optimal roller bearing forming machining cutting method is proposed based on the internal tooth interference...
Proceedings Article
Shift Schedule of Automatic Transmission of Construction Vehicle Based on Matlab/Simulink
Liangjie Guan, Tiezhu Zhang, Yongzhi Ma
Aimed at the problem of engineering vehicle hydraulic mechanical transmission system efficiency is low.Thispaper mainly study of the engineering vehicle automatic transmission shift schedule.Through the artificial set the minimum numerical efficiency,this paper obtained the automatic transmission shift...
Proceedings Article
Research of the Optimal Shape of Bathtub
Rong Wu
We take heat transfer between water and air and heat dissipation capacity of bathtubs into consideration and discuss the influence of bathtub shapes on temperature. We keep the temperature of bathtub in 39 degrees Celsius.We assume that the bathtub's capacity is the same and try to find the best shape...
Proceedings Article
Analysis in the heat transfer process of water in a bathtub with and without bubbles
Jidong Li
This paper proposed a basic model and an optimized model to obtain the temperature field of water in a bathtub with and without bubbles. Firstly, the basic heat transfer model is established based on the three-dimensional N-S equations, the heat transfer differential equations and cuboid boundary conditions....
Proceedings Article
Study on the influence of the slope-angle to the bullet projectile
Li-zhi Yang, Yong-cai Cheng
The engraving process of projectile is a very complicated mechanics process,In this paper, the artillery projectile engraving tube process is the research object, using the WDW-T200 microcomputer control electronic universal tension and compression testing machine of projectile and barrel samples of...
Proceedings Article
Accuracy Measuring For the RV Reducer Cycloid Gear and Manufacturing Error Analysis
Yueming Zhang, Guoyang Zhu
RV reducer is an important function part of industrial robot joints. The cycloid gear measuring problem is the key part of high precision RV reducer manufacturing. A brief introduction to the forming principle and formulas of RV reducer cycloid tooth contour. A new method for measuring the contour accuracy...
Proceedings Article
Optimal Wheelchair Passenger Service in the Airport
Anran Zheng
This paper uses a queuing model of multi-server system to offer optimal airport wheelchair service which minimizes the cost and offers service of high quality. It addresses the performance of airport wheelchair service associated with the waiting time of passengers who need the service. According to...
Proceedings Article
Research of Water Hammer of Air Conditioning Chilled Water System Based on Flowmaster
Bo Liu, Hehui Wang, Ye Huang, Guilin Tang, Chenqiong Ye
Water hammer phenomenon often occurs in the high-rise buildings air conditioning chilled water system, and cause enormous damage. With the help of Flowmaster platform, network model was built to simulate water hammer with different pipeline models, and the simulation results show that the water hammer...
Proceedings Article
Finite element analysis to the multi-layer U-shaped bellows' strength and axial stiffness
Shidong Wen, Hehui Wang, Guilin Tang, Xueyi Yin, Meng Gao
The multilayer U-shaped bellows' strenth and axial stiffness are studied by ANSYS finite element analysis. The plane axisymmetric model of multilayer bellows is established, and the material nonlinear, geometric nonlinearity and contact between the layers of multilayer bellows is considered, obtained...
Proceedings Article
Numerical simulation of pipeline ultrasonic cavitation based on CFD
Zhihua Wang, Hehui Wang, Chaoping Wang, Chunhui Fu, Pangu Lu
Cavitation effect is one of the main mechanisms of ultrasonic descaling. Through the mixture model and the cavitation model in Fluent, the ultrasonic cavitation field in the pipe is simulated. The simulated distributions of pressure field and variation of vapor are analyzed and discussed. This study...
Proceedings Article
Some key Techniques Research Based on Five-axis Matching of The Integral Impeller
Chun-guang Gu, Zhu-ming Cao, Hong-mei Sun
Integral impeller is the key component of aeroengine, which reflects the development level of a country's equipment manufacturing industry. The function, technical requirements and processing difficulty were introduced in the paper. The machining processes of a axial-flow impeller was described. The...
Proceedings Article
Finite-element Analysis of Spherical BOP in Snubbing Service of Gas Well
Longqing Zou, Chongpeng Yu, Junli Shao
In snubbing service, the spherical BOP plays a vital role in shut-in well and running and pulling tubing. The shell and rubber core are the crucial components of spherical BOP, taking the three-dimensional software SolidWorks as a platform, these two components 3D model have been established, and the...
Proceedings Article
Roots Blower with Gradually Expanding Outlet Gap: Mathematical Modelling and Performance Simulation
Yingjie Cai, Ligang Yao
Gradually expanding gap in the outlet of the Roots blower can effectively reduce the backflow impact and the noise of the blower. The working principle for the Roots blower with the gradually expanding gap is investigated in this paper. And the mathematical modelling for backflow is proposed. Numerical...
Proceedings Article
Determination of Main Laser Processing Technical Parameters in Wood Manufacturing
Honggang Zhao, Junhua Wu, Yanlong Liu, YaoXing Sun
According to the laser cutter larch, this study has determined the reasonable process parameters such as focal length, light intensity, and optimized laser processing technology parameters to provide test methods. Firstly, for the cutting seam state analysis the precautions of software settings have...
Proceedings Article
A Design Method for Composition and Reuse Oriented Weaponry Model Architecture
Meng Zhang, Hong Wang, Yiping Yao
Weaponry model architecture oriented to composition and reuse can improve modeling efficiency and ensure consistency of models, for developers can build weapon models by model composition and reuse. However, there are massive models in the field of military equipment, and the combination and inheritance...
Proceedings Article
The Project Design of the Tracked Vehicle Hydraulic Mechanical Differential Steering
Zhaozhong Yang, Liwei Wang, CaoYang Shi
Based on the principle of hydraulic mechanical stepless transmission is tracked vehicle hydraulic mechanical differential steering system can effectively improve the vehicle's steering can win, is has good prospects for development of a tracked vehicle steering model. Papers on tracked vehicle and its...
Proceedings Article
Study on the Unified Mathematical Model for All Types of Cam Mechanisms
Wei He, Xueming He, Feng Xu, Jiujun Zhen, Rong Zhang
This paper presents the unified mathematical model well applicable for the analysis and design of the planar and spatial cam mechanisms of all categories in terms of the differential geometry and meshing principle, exploring the interrelation of the various cam mechanisms. The general-purpose CAD/CAM...
Proceedings Article
Research on the Topography Model of Micro Wire Electrical Discharge Machining Surface
Haijuan Ding, Xiaohai Li, Xinrong Wang, Libin Guo, Liping Zhao
Micro Wire Electrical Discharge Machining (Micro-WEDM) surface consists of many approximate spherical peaks and craters with interphase distribution. According to the micro- WEDM mechanism, the surface micro-topography is simulated by using ANSYS, and the mathematical models about single crater and multi-crater...
Proceedings Article
Integrated BOM model oriented to manufacturing process of complex product
Lin Lin, Xiaobing Liu, Wei Mu, Hongguang Bo, Dongjuan Xue
The static bill of material data and dynamic bill of process data need to be integrated during manufacturing process of complex product, in order to wholly control the workpiece of workshop and systematically consider material requirements planning and enterprise resource planning. This paper constructed...
Proceedings Article
The investigation of AlGaN/GaN HEMT failure mechanisms under different temperature conditions
Chunsheng Guo, YunXiang Ren, Li Gao, Hui Zhu, Shiwei Li
To explore degradation law and failure mechanisms of AlGaN/GaN HEMT under different temperature conditions, the step-temperature stress experiments are carried out. The results show that the drain-source current decreases with the aging time when the junction temperature range from 139 to 200 ; while...
Proceedings Article
Investigation into the Self-loosening Trend of Bolt Joints on the Tower Crane
ShengChun Wang, PeiWei Ni, Ye Zhang, MingXiao Dong
In this paper, a three-dimensional finite element model is developed based on the joints on standard sections of tower crane QTZ5510. The validity of this finite element model is verified through the contrast of analytical results calculated by Yamamoto Method and simulated ones under the action of static...
Proceedings Article
A Study on Fault Diagnosis of Redundant SINS with Pulse Output
Yinan Wang, Zijun Ren, Kaikai Dong, Kai Chen, Jie Yan
The missile-based redundant SINS (strap-down inertial navigation system) output the measurement data by using pulse quantization. Pulse quantization can disorganize the errors in the original measurement signal, cause an instantaneous drift of 50 degree/hour, and thus brings about great difficulty to...
Proceedings Article
The New Cryogenic Superfluid Gyroscope Based On Matter Wave Interference Effects
Mao-lin Deng, Yun-ting Zhou
In this paper, the physical mechanism of the cryogenic superfluid gyroscope based on AC Josephson effect are analyzed , meanwhile, the implementation of the cryogenic superfluid gyroscope was brought up and the advantage of the sensitivity of the gyroscope is proved by theoretical derivation. A method...
Proceedings Article
Research on the Production Process of the Equipment Quality Supervision Information Construction
Feng Liang, Hai Wei Bai, Qian Li
With the rapid development of information technology, the production and management of the equipment towards to the direction based on digital, network and intelligent, which promote the revolution through the design instrumentalities, production process and testing technology. Nowadays, a new generation...
Proceedings Article
The structure design and simulation analysis for the corn seedling mechanism of transplanting machine
Yujie Song, Jun Hu
In order to achieve the efficient transplanting of corn pot seedling in the field, and to avoid the seedlings injuries result from separation between seedling and pot with traditional ways. A kind of seedling mechanism is designed which the main body is disc cutter, and the structure of the disc cutter...
Proceedings Article
Stability analysis of milling with variable pitch tools considering the variable cutting force coefficients with spindle speed
Gang Jin, Zhanjie Li, Jianxin Han, Hua Li
The combination of increased strain rate and thermal softening of the workpiece at higher cutting speeds will cause the change of cutting force coefficients. In this paper, a vibration model for milling process, which can consider the variable cutting force coefficients (VCFC) with the spindle speed...